Autotype PLUS 2000 – Diazo double photopolymer emulsion (dual cure) for varnishing and printing with solder inks. The diazo does not dissolve with water but is directly added to the emulsion. The ready emulsion can be used for 4-5 weeks.
Autotype PLUS 6000– Diazo double photopolymer emulsion (dual cure) for textiles. For printing with plastisols and water based paints. The diazo does not dissolve with water but is directly added to the emulsion. The ready emulsion can be used for 4-5 weeks.
Autotype PLUS 7000-Diazo dual photographic emulsion (dual cure) for graphic printing. Fine-resolution, high-resolution images. It is also recommended for varnishing. The diazo does not dissolve with water but is directly added to the emulsion.
Autotype PLUS 8000-Diazo dual photographic emulsion (dual cure) for graphic printing. Fine-resolution, high-resolution images. Holds high prints. The diazo does not dissolve with water but is directly added to the emulsion.
Autotype PLUS 9000-Diazo photopolymer mono emulsion (dual cure) for thick printing.
Autotype PLUS TX-Diazo photopolymer dual cure for textile. For printing with plastisols and water based paints. The diazo does not dissolve with water but is directly added to the emulsion. The ready emulsion can be used for 4-5 weeks.
CPS Quick Haze– Solvent-based quick release agent for haloes. Environmentally friendly. Apply on a wet or dry sieve with a brush and wash after 10-15 minutes. There is no odor of chlorine.
CPS Stencil Remover Concentrate–Stripper Concentrate for Manual and Machine Stripping. With manual tattooing, it is recommended that the dilution be 1:25 to 1: 30-1: 35. For machine pulling it can be diluted to 1:80.
CPS Ultra Coat WR Filler-Filler for templates. Resistant to water.
CPS SR Filler Blue-Filler for templates for varnishing and printing with solvent inks. Resistant to thinners.
CPS Haze Remover HV–CPS Haze Remover HV – environmentally friendly, low-base halo removing gel. A thin layer of the preparation is applied on both sides on a dry sieve with a sinking sack or brush and left to dry (but not in direct sunlight) until the coating looks like flour. The preparation can stay for days without damaging the sieve. Once it has dried, the screen is smeared with activator K3 or V3. After 5-10 minutes, wash with water. It is recommended that the screens be coated with the preparation at the end of the working day and that in the morning they should be treated with an activator and washed with water. The results are very good.
CPS Hardener WR– Hardener – template lock. Apply on both sides of the template (exposed, exposed and dried) with a sponge. Allow to dry. It can be dried with warm air.
CPS Fast Acting Haze Remover– Fast-acting halo removing paste with a high content of bases. Stir well before use. Apply on a wet sieve with a brush and wash after about 7-10 minutes.
CPS Haze Hunter – New generation of fast-acting Haze remover.
CPS Screen Wash K3-Hand wash of screen – to remove inks before pulling. Flash Point 42??. Not harmful by inhalation. Used as an activator of CPS Haze Remover HV. It can be recirculated. Used to wash countertops and machines (instead of nitro).
CPS Screen Wash V3– Hand and machine wash screed – to remove inks before pulling. Flash point 62oC. Not harmful, with minimal aroma content, no danger. Used as an activator of CPS Haze Remover HV. It can be recirculated. Used to wash countertops and machines (instead of nitro).
CPS Screen Cleaner Vx– Manual and machine wash of screens and swabs – to remove inks from unwrapped patterns. Flash point 62oC. Not harmful, does not contain any aromatic compounds and emulsifiers without a hazard. It can be recirculated.
CPS Degreaser concentrate 1:10/15 – Degreaser-concentrate. Diluted with water in a ratio of 1:10 to 1:15. Gives better bonding of the emulsion and a higher resistance to the pattern.
CPS Screen Adhesive MF Red 1.1 kg–Two-component adhesive for mesh.
Takter 330-Spray toner – Increases the blackness of the image and the clarity of the lines.
Aprimaglia spray starter-Cleaner spray based on slow evaporation solvents. Cleaner spray based on slow evaporation solvents. It removes traces of ink, glue, adhesive tapes, felt pen or ink writings from iron, cardboards, plastics, wood, residual of labels, adhesives, Test the product on already painted surfaces. Leave it acting for a few seconds and then remove. It eliminates grease, glue, incrustations, ink It removes the labels Low evaporation Colourless.
Silicone Extra-Silicone spray with medium viscosity. It serves against bonding in the production (extrusion / injection molding) of rubber, polyurethane, plastics, leather. Resistant to high temperatures and does not injure rubber and plastic materials. Good lubricant for locks, locks, curtain rods, drawers, hinges, hinges, spools, rolls, threads, threads. Do not leave greasy traces or dirt.
Takter 2200– Water-based countertops. The adhesive is diluted with water in a ratio of 1: 1 to 1: 3. A very thin layer of glue is applied to the countertop only on the surface where the fabric is to be glued and dried for a few seconds. Apply with brush, foam roller or sprayer. If the glue is contaminated (cloth residue), the glue is wiped with a wet cloth. The cost rate for t-shirts is 1 application for about 300-500 pcs. The glue is washed with CPS Screen Wash K3 or CPS Screen Wash V3. Apply the preparation on the counter, wait for 3-5 minutes, then wipe with a spatula or rag.
Different types of sizes.Color white and yellow.
Plastisol inks– For textile printing. Suitable for printing all natural and synthetic textiles. Very good coverage. Soft and elastic.
Water based–Highly coverage textile ink. Suitable for printing on dark fabrics without a pad.Transparant, roof, inflatable, glyter, etc. bases / pastes. Self-fixing.
Pigment pastes-Additives and auxiliaries (catalysts, retarders, thickeners, thinners, transfer powders, etc.)
Solvent inks PVC-For screen printing on flexible and rigid PVC film, plexiglass, paper, cardboard, banners and any other plastic materials. The ink has good coverage and gloss. Suitable sieve to work from 90 to 180. All colors in the series can be mixed.
Tampoprint-Pad printing ink suitable for various types of materials such as PVC, polycarbonate, polystyrene, paper, plastic, plexiglass.
UV Inks–Suitable for printing on all types of surfaces, raster and fine images. With very good coverage.
GLITTER AND PEARL
– Silver and gold glitters with a size of 0,004 mm
– A wide range of color glitters with a size of 0.008 mm
– Transparent glitters
– Transparent beads